Electricians
in Salt Lake City, UT

Evening trips usually point to a “stacking” problem rather than one bad device. After work hours, homes tend to run more lighting, cooking loads, entertainment gear, chargers, and sometimes space heaters—all on top of whatever cycles automatically. That combined demand can push a circuit that’s already near its limit. Heat also matters: connections and breakers can behave differently once they’ve warmed up. If it repeats under similar conditions, treat it as a warning that the circuit or a connection is being stressed.

New bulbs don’t rule out electrical causes. Flicker can come from a loose or aging connection, a worn switch, a shared neutral issue, or voltage changes when larger loads start up. The pattern is the clue: a brief dip when a motor starts is different from random shimmer that shows up across multiple fixtures. If you notice flicker in more than one room, or it comes with buzzing, warm plates, or a faint odor, that’s less “annoying” and more consistent with a connection degrading.

Intermittent power is more than an inconvenience because it often indicates a contact that’s no longer firm. When a connection makes and breaks under load, it can arc and create localized heating that stays hidden behind the cover plate or in a box. People often discover it only after a plug feels warm, a device acts erratic, or they catch a plastic smell. Even with small loads, a loose connection tends to worsen over time and can affect other outlets tied into the same run.

A light “hot plastic” smell without visible damage can be an early sign of overheating at a contact point. Switches and splices can run warm when resistance increases, and the first evidence is sometimes odor that appears only when the light is on or a certain load is active. It’s also common for the wall to feel slightly warmer or for the switch to feel different when pressed. When smell shows up intermittently, it’s easy to dismiss, but it’s often the earliest warning you’ll get.

A panel can “work” while still aging in ways that reduce safety and reliability. Subtle signs include breakers that run warmer than others, plastic that looks darkened, a loose-feeling breaker fit, or noise that appears only under heavier household use. Modern homes also draw power differently than they did years ago—more electronics, more chargers, and more simultaneous loads. That shift can expose weaknesses that stayed hidden for a long time. Problems often show up abruptly after months of quiet stress, not gradually.

Yes. Storm-related surges don’t always cause a full outage or a tripped breaker. Sometimes the result is “soft damage” that shows up as sensitive electronics behaving inconsistently—random resets, buzzing audio, chargers running hot, or lights that seem less stable. Surges can also stress connections and components so they’re more likely to fail later. When the timing lines up right after a storm, it’s worth taking seriously even if the home still has normal lighting and the panel looks unchanged at a glance.

Sounds from a wall near electrical devices shouldn’t be written off as normal settling. Crackling can indicate arcing at a loose connection, a conductor that’s moving slightly, or insulation that’s being stressed by heat. It may only happen when a particular load is running, like a heater, refrigerator, or vacuum, which makes it easy to miss. The concern is that the activity is hidden and can continue for a long time before any visible sign appears. The longer it persists, the more likely damage accumulates.

Rooms that look similar rarely share identical electrical conditions. One circuit may feed extra outlets, lighting, bathroom fans, or a portion of another area, so the “starting point” load is already higher. Circuit length and connection quality also matter; a slightly loose splice can add resistance, creating more heat and making a breaker react sooner. If the same appliance reliably trips one area but not another, that’s useful information: it suggests a circuit-specific limitation or weakness rather than a random breaker mood.

Once surfaces come off, it’s common to find older decisions that were hidden by finished walls: splices outside proper boxes, mixed wiring types from different eras, overloaded branches that were extended “just one more time,” or cable jackets that have become brittle. You may also see evidence of past heat—darkened insulation or warped device boxes—without any history of a fire. Remodeling is often when a home reveals where it has been operating close to its limits, and it’s a chance to understand those constraints before everything is sealed back up.

A mild “tingle” can be a sign that current is finding an unintended path, often related to grounding problems, leakage through electronic filters, or wiring that isn’t bonded the way it should be. It may feel minor, but the conditions matter: bare feet, concrete floors, and damp areas make it more noticeable and can raise risk. Even if the device still works normally, that sensation suggests the electrical system isn’t controlling fault current the way it’s meant to. Over time, what feels like a nuisance can become a genuine hazard.

A brief, slight dip can happen when a motor or compressor starts, but repeated or dramatic dimming suggests the circuit is experiencing noticeable voltage drop. That can come from heavy shared loads, long runs, or resistance at a worn connection in a panel, junction, or device. The “where” helps interpret it: if the whole house dips, the issue may be upstream; if only one zone does, it’s more likely localized. Persistent dimming tends to worsen as connections heat and age, and it can shorten the life of electronics and lamps.

Older wiring often shows its limits through behavior rather than a single dramatic failure. Watch for frequent nuisance trips, outlets that feel warm, a need to “manage” which appliances can run together, or electronics that act finicky in ways that don’t match the device quality. Another clue is layering: past owners may have added new receptacles onto old branches, increasing demand without increasing capacity. A home can run like this for years, but the risk is that heat builds gradually at weak points, staying invisible until it becomes serious.

Changes in how a switch feels often reflect internal wear or heat-related damage at the contacts. It may continue to turn lights on and off, yet the connection can become less stable, increasing resistance and making the device run warmer over time. Sometimes this shows up alongside small clues: a slight odor when the light is on, occasional flicker, or a faint snap sound. Because it’s gradual, people adapt to it and stop noticing. Treat a change in “feel” as an early indicator, not just a cosmetic annoyance.

Dry winter air makes static discharges more noticeable, so people often assume the wiring is at fault. Static itself usually isn’t a sign of failing electrical work, but it can distract from real issues or make grounding-related problems feel worse. The key difference is consistency: occasional shocks from doorknobs are typical in dry conditions, while repeated tingles from appliances, unusual buzzing, or new flicker patterns point to something else. If winter coincides with new electrical oddities, it may be seasonal timing rather than the cause, but it’s still worth attention.

Yes, localized symptoms often trace back to a specific branch circuit or connection point serving that part of the home. A loose splice, a tired device connection, or an overloaded run can create voltage drop and fluctuation under normal household cycling, which is hard on chargers and shortens lamp life. The fact that it’s geographically consistent within the house is meaningful; it helps separate a whole-home supply issue from a problem in one distribution path. These conditions rarely self-correct and typically become more obvious as heat and oxidation increase resistance over time.